The N76E003AQ20 is an embedded flash memory type based on an 8-bit high-performance 1T 8051 microcontroller.
The instruction set is fully compatible with the standard 80C51, with enhanced performance.
Yi Jie continued with the introduction.
The new Tang N76E003 contains up to 18K bytes of main flash memory, called APROM, where the content of the user code resides. The N76E003 flash memory supports the Application Programming (IAP) feature, which enables on chip firmware updates. IAP can also configure any block of the user code array to be used as a non-volatile data storage, written by IAP and read by IAP or MOVC instructions. There is also an additional flash called LDROM, which is typically located in the boot code used to perform system in system programming (ISP). The size of LDROM can be configured to 4K bytes. For the convenience of programming and verification, Flash allows for electronic programming and reading through parallel writers or online programming (ICP). Once the password has been confirmed, the user can lock the password to ensure security.
The New Tang N76E003 provides a wide range of peripherals, including 256 bytes of SRAM, 768 bytes of auxiliary RAM (XRAM), up to 18 universal I/Os, two 16 bit timers/counters 0/1, a 16 bit Timer2 module with three channel input capture, a watchdog timer (WDT), a self wake-up timer (WKT), and a 16 bit automatic overload Timer3 universal or baud rate generator, Two UART recognition with frame error detection and automatic address, one SPI, one I2C, five enhanced PWM output channels, all eight channels share pin interrupt I/O and one 12-bit ADC. The peripheral is equipped with 18 signal source capabilities with 4-level priority interrupts.
The New Tang N76E003 is equipped with three clock sources and supports instant switching through software. Their three clock sources include an external clock input, a 10 kHz internal oscillator, and a 16 MHz internal precision oscillator that is factory adjusted to ± 1% at room temperature. The N76E003 provides additional power monitoring, power-on reset, and 4-level power-off detection, which can stabilize the power-on/power-off sequence for high reliability system design.
The operation of the new Tang N76E003 microcontroller consumes very low power and has two economical power modes: reduced power consumption - idle and power down modes are software selectable. Idle mode turns off the CPU clock, but allows for continued peripheral device operation. Power off mode will stop the entire system clock from consuming low power. The system clock of N76E003 can also be reduced by software clock to achieve flexibility between execution performance and power consumption.
With a high-performance CPU core and a wealth of carefully designed peripherals, the New Tang N76E003 can meet universal requirements for the completion of household appliances or motor control systems.
Central processing unit:
A fully static designed CMOS microcontroller based on 8-bit high-performance 1T 8051.
The instruction set is fully compatible with MCS-51.
-4 priority interrupt function.
- Dual Data Pointer (DPTR).
Action:
Wide power supply voltage ranging from 2.4V to 5.5V.
A wide operating frequency of up to 16 MHz Industrial temperature level: -40 ℃ to+105 ℃.
Memory:
APROM with a maximum capacity of 18K bytes can be used for user code.
The configurable 4K/3K/2K/1K/0K byte LDROM provides flexibility for user developed startup code Flash memory, 128 bytes per page.
- Built in Application Programmable (IAP).
- Secure password lock.
256 bytes of on-chip RAM.
- Additional 768 bytes of on-chip auxiliary RAM (XRAM) accessed through the MOVX instruction.
Clock source:
When VDD is 5.0V, the 16 MHz high-speed internal oscillator is adjusted to ± 1% and in all cases to ± 2%.
-10 kHz low speed internal oscillator.
External clock input Switch the clock source in real-time through software.
Programmable system clock divider, up to 1/512.
Peripheral devices:
Up to 17 universal I/O pins and 1 input only pin. All output pins have separate 2-stage swing rate control Standard interrupt pins and pins.
Two 16 bit timers 0 and counter 1 compatible with standard 8051 You can choose a 16 bit timer 2 with a three channel input capture module and 9 input pins.
A 16 bit automatic reset timer 3 that can serve as a baud rate clock source for UART.
A 16 bit PWM counter interrupt of the timer.
A programmable watchdog timer (WDT) with a dedicated 10 kHz internal source providing the clock.
A dedicated self wake-up timer (WKT) for self timed wake-up in power saving mode.
Two full duplex UART ports with frame error detection and automatic address recognition capabilities. The RXD pins of TXD and UART0 can be interchanged through software.
- An SPI port with master and slave modes, 8 Mbps high when the system clock is 16 MHz.
One I2 has a C bus with both master and slave modes, with a high data rate of 400 kbps.
Three pairs, six channel pulse width modulator (PWM) outputs, with 10 output pins available for selection. 16 bit resolution, with different modes and fault braking functions, used for motor control.
Eight pin interrupt channels, shared by all I/O ports, with variable configuration detection for edges/levels.
-1 12-bit ADC with a conversion rate of up to 500 ksps, hardware triggered and conversion results that facilitate motor control.
Energy management:
There are two power saving modes: idle and power down.
Power monitor:
- Under voltage detection (BOD) with low power consumption mode, 4-level selection, interrupt or reset options.
Power on reset (POR).
Powerful ESD and EFT.
Development tools:
Nuvoton On Chip Debugger (OCD) with KEILTM development environment.
- Nuvoton Online Programmer (ICP).
- Programming within the Nuvoton system (ISP) through UART
新唐N76E003AQ20包含多達18K字節的主閃存，稱為APROM，其中用戶代碼的內容居住。 N76E003閃存支持應用程序內編程（IAP）功能，該功能可啟用片內固件更新。 IAP還可以將用戶代碼陣列的任何塊配置為用作非易失性數據存儲，由IAP寫入并由IAP或MOVC指令讀取。 還有一個額外的閃光燈稱為LDROM，通常位于其中的引導代碼用于執行系統內編程（ISP）。 LDROM的大小可配置為4K字節。 為了方便編程和驗證，F(xiàn)lash允許通過并行寫入器或在線編程（ICP）進行電子編程和讀取。 一旦密碼已確認，用戶可以鎖定密碼以確保安全。
新唐N76E003AQ20提供了豐富的外設，包括256字節的SRAM，768字節的輔助RAM（XRAM），向上到18個通用I / O，兩個16位定時器/計數器0/1，一個具有三通道輸入捕捉的16位Timer2模塊，一個看門狗定時器（WDT），一個自喚醒定時器（WKT），一個16位自動重載Timer3通用或波特率發生器，兩個帶幀錯誤檢測和自動地址的UART識別，一個SPI，一個I2C，五個增強型PWM輸出通道，所有通道的八個通道共享引腳中斷I / O和一個12位ADC。 外設配備18個帶有4級優先級中斷的信號源能力。
新唐N76E003AQ20配備了三個時鐘源，并支持通過軟件即時切換。 他們?nèi)齻�時鐘源包括外部時鐘輸入，10 kHz內部振蕩器和一個16 MHz內部精密振蕩器在室溫下出廠時調整為±1％。 N76E003提供額外的電源監控上電復位和4級掉電檢測等檢測，可穩定上電/斷電序列用于高可靠性的系統設計。
新唐N76E003AQ20微控制器的操作消耗了非常低的功率，并具有兩種經濟的功率模式：降低功耗－空閑和掉電模式是軟件可選的。 空閑模式關閉CPU時鐘，但允許繼續外圍設備操作。 掉電模式會停止整個系統時鐘低功耗。 N76E003的系統時鐘也可以通過軟件時鐘來降低分頻器，可以在執行性能和功耗之間實現靈活性。
憑借高性能的CPU內核和豐富的精心設計的外設，新唐N76E003可以滿足通用要求目的，家用電器或電動機控制系統的完成情況。
中央處理器：
–全靜態設計的基于8位高性能1T 8051的CMOS微控制器。
–指令集與MCS-51完全兼容。
– 4優先級中斷功能。
–雙數據指針（DPTR）。
操作：
– 2.4V至5.5V的寬電源電壓。
–高達16 MHz的寬工作頻率。 –工業溫度等級：-40℃至+ 105℃。
記憶：
–多可達到18K字節的APROM用于用戶代碼。
–可配置的4K / 3K / 2K / 1K / 0K字節LDROM，為用戶開發的啟動代碼提供了靈活性。 –閃存存儲器，每頁128個字節。
–內置的應用內可編程（IAP）。
–安全密碼鎖。
– 256字節片上RAM。
–通過MOVX指令訪問的附加768字節片上輔助RAM（XRAM）。
時鐘來源：
–當VDD 5.0V時，16 MHz高速內部振蕩器調整為±1％，在所有情況下均調整為±2％。
– 10 kHz低速內部振蕩器。
–外部時鐘輸入。 –通過軟件實時切換時鐘源。
–可編程系統時鐘分頻器，高可達1/512。
外圍設備：
–多達17個通用I / O引腳和1個僅輸入引腳。 所有輸出引腳均具有單獨的2級壓擺速率控制。–標準中斷引腳和腳。
–兩個與標準8051兼容的16位定時器0和計數器1。–可以選擇一個帶三通道輸入捕獲模塊和9個輸入引腳的16位定時器2。
–一個16位自動重裝定時器3，它可以作為UART的波特率時鐘源。
–定時器的一個16位PWM計數器中斷。
–一個由專用10 kHz內部源提供時鐘的可編程看門狗定時器（WDT）。
–一個專用的自喚醒定時器（WKT），用于在省電模式下進行自定時喚醒。
–兩個具有幀錯誤檢測和自動地址識別功能的全雙工UART端口。 TXD和UART0的RXD引腳可通過軟件互換。
–一個具有主模式和從模式的SPI端口，當系統時鐘為16 MHz時高8 Mbps。
–一臺I2具有主模式和從模式的C總線，高數據速率為400 kbps。
–三對，六個通道的脈寬調制器（PWM）輸出，可以選擇10個輸出引腳。16位分辨率，具有不同的模式和故障制動功能，用于電機控制。
–八個引腳中斷通道，所有I / O端口共享，具有邊沿/電平的可變配置檢測。
– 1個12位ADC，轉換速率高達500 ksps，硬件觸發并轉換結果比較促進電機控制。
能源管理：
–兩種省電模式：空閑和掉電模式。
功率監控器：
–具有低功耗模式的欠壓檢測（BOD），4級選擇，中斷或復位選項。
–上電復位（POR）。
強大的ESD和EFT。
開發工具：
–帶有KEILTM開發環境的Nuvoton片上調試器（OCD）。
– Nuvoton在線編程器（ICP）。
–通過UART的Nuvoton系統內編程（ISP）
MAX3232IPWE4 null
MAX3232IPWR null
MAX3237ECPW null
MAX3238CPW null
MAX3238CPWR null
MAX3238ECPW null
MAX3238EIPWR null
MAX3238IPW null
MAX3238IPWR null
MAX3243CPW null
MAX3243CPWE4 null
MAX3243CPWG4 null
MAX3243CPWR null
MAX3243CPWRG4 null
MAX3243ECPW null
MAX3243ECPWR null
MAX3243EIPW null
MAX3243EIPWG4 null
MAX3243EIPWR null
MAX3243IPW null
MAX3243IPWG4 null
MAX3243IPWR null
MAX3318CPWR null
MAX3318ECPW null
MAX3318ECPWR null
MAX3318EIPWR null
MAX3318IPWR null
MAX3386ECPW null
MAX3386ECPWG4 null
MC3303PWR null
MC3303PWRE4 null
MC3403PWR null
NE555PW null
NE555PWE4 null
NE555PWG4 null
NE555PWR null
NE555PWRE4 null
NE555PWRG4 null
P82B96PW null
P82B96PWR null
PCA9515APWR null
PCA9518PW null
PCA9534APW null
PCA9534APWR null
PCA9534PW null
PCA9534PWR null
PCA9535PW null
PCA9535PWR null
PCA9538PW null
PCA9538PWR null
PCA9539PW null
Texas Instruments, Inc. PCN# 20120822001
PCA9539PWG4 null
PCA9543APW null
PCA9545APWR null
PCA9546APW null
PCA9546APWG4 null
PCA9546APWT null
PCA9548APW null
PCA9548APWR null
PCA9554APW null
PCA9554APWR null
PCA9554PW null
PCA9554PWG4 null
PCA9555PW null
PCA9555PWE4 null
PCA9555PWR null
PCA9557PW null
PCA9557PWR null
PCF8574APW null
PCF8574APWR null
PCF8574PW null
PCF8574PWR null
PCF8575CPW null
PCF8575CPWR null
PCF8575PW null
PCF8575PWG4 null
PCF8575PWR null
RC4558IPWR null
RC4558PWR null
RC4580IPW null
RC4580IPWR null
SN65C1168EPWR null
SN65C1168PW null
SN65C1168PWR null
SN65C3221EPW null
SN65C3221EPWG4 null
SN65C3221EPWR null
SN65C3221PW null
SN65C3221PWR null
SN65C3222EPW null
SN65C3222PW null
SN65C3223EPW null
SN65C3223EPWG4 null
SN65C3223EPWR null
SN65C3223PWR null
SN65C3232EPW null
SN65C3232EPWR null
SN65C3232PW null
SN65C3232PWR null
SN65C3238PW null
SN65C3238PWR null
SN65C3243PWE4 null
